How to Install Metal Roofing | Easy 4 Step Guide

How to install metal roofing can be a difficult task; on the off chance that you choose to introduce a rooftop yourself or on the other hand, if you believe a thought of what you should expect when the experts come, you can follow these steps toward begin.

If you are in the process of renovating your home and want to add style, comfort, safety, and a good lifespan, a metallic roof is the best option. This guide will teach you the quick and easy steps on how to install metal roofing perfectly.

Metal Roofing Checklist | How to install metal roofing

First, you must make sure you have all the necessary materials to do the installation. This way, you save time and money by going to the hardware store several times.

Checklist for metal roofing installation:

Step #1, Start Square

When installing metal roof panels, the first thing to do is to ensure that you start square. This indicates that the vertical lines are square to the eaves.

It is essential to start square because if the first panel is a little crooked, all the panels that come after it will also be crooked. When starting the roof, square the edge and adjust the panel if necessary. For example, if this specific roof were slightly off, even by half an inch, you would have to tilt the panel a little to make it square, starting with the first panel.

Step #2 Cutting Panel to Length & Add Eave Trim 

If the panel you are using is too long. When installing an eave with exposed fasteners, it should overhang the eave by an inch and a half or two at most. Place the tape against the end wall and measure down to the edge of the eave molding.

For a 24-inch measurement, you should turn the panel over and make marks on the back. Remember to add an inch and a half so that you will make a 25.5-inch mark. And repeat the same thing on the other side. You can join those two lines using a square or a straight edge to create your cut line.

Next, you need to cut through the female and male ribs to get to the flat part of the panel. Using duckbill scissors to ensure a clean edge, I’m going to cut through the flat part of the panel. It is essential to wear gloves during this process. Finally, cut the female rib. You next have a panel that has been cut to 25.5 inches so that 1.5 inches can protrude into the eave and is ready to be installed.

Step #3 Seal | How to install metal roofing

Where two ends of the trim meet, you will connect them together. First, cut the bottom hem of the overlapping trim at an angle. After installing the lap molding, apply a sealant to the top. Open the bottom hem of the overlapping molding and slide it over the angle-cut hem of the overlapping molding.

Step #4 Install and Secure it

To cover the roof, lay a line of exterior sealing strips with butyl tape 10 cm from the top of the peak; this is where you will attach the ridge cap to the roof with screws. Apply a bead of sealant to the foam closure, then install the ridge cap on the peak and connect it with two-inch screws to the roof deck through each rib.

With the roof cap complete, you will have the result that all the water that falls on the roof will run off without ever touching the subfloor.

Types of Metal Roofing

Metal roofing shingles can closely mimic asphalt or slate shingles but with the advantages of metal.

The type of materials used to manufacture metal roofing varies, and the most common are tin, zinc, steel, aluminum, and copper. There are four main types of metal roofing: metal shingles, corrugated or through panels, modular panels, and standing seam panels.

Corrugated Panels

This type of metal roofing is probably the most recognizable and resembles a tin or steel barrel. One large panel lays on your home, similar to shingles but is usually thicker, heavier, and stronger than other types. In addition, they come in different colors, which you can paint right over if desired or left as-is for natural aesthetics.

Modular panels

Modular panels are made of thin metal parts that fit together. They are often used in commercial applications, which can be applied to roofs or building walls. As a result, you’ll have visual appeal for homeowners who want the look and durability of galvanized steel in their homes.

Standing Seam Panels

This type of metal roofing is a solid and durable option that allows panels to overlap each other. It is mainly used on commercial buildings but also works well for some residential installations.

Get Professional Assistance

Remember that in order to achieve high quality and ensure that you are installing authentic and brand new metallic roofs, you must hire professionals. As a result, you will have a fantastic and perfect installation service.

If you are looking for an experienced team with outstanding results and true professionalism, get in touch with us! At High Level Roofing LLC, we ensure complete satisfaction with all of our services. Get in touch with us to know more about our Metal Roofing Service and others!